|
Personality PlugsTM
The Xeptor®
Electrical Interface
Personality plugs are small connector
conversion modules about as big as the last segment of your little
finger. They are used to convert the 8pin header in the Xeptor to
any of many available connector styles and pin assignments common in
the industry. For example, there is one Personality Plug type for
each of the older Coin Mechanisms CC-series acceptors and the
NRI
multi-wire output acceptors. Additionally, many have been designed
to meet the needs of specific OEMs, including such things as
simulation of OEM credit optics module signals. Other special
interface requirements are easily satisfied with new Personality
Plugs designed specifically for the job. With the correct
Personality Plug installed in an Xeptor, retrofit installation
requires no machine connector re-wiring! The tables below can help
you decide which Personality Plug to use. The electrical
specification for each pin definition are found in the 3rd table
below.
Personality
Plug Model: |
PP16 |
PP16IC |
PP40 |
PP46 |
PP62 |
PP3337 |
PPUNI |
Compatibility
Connector |
CC-16
JST-6 |
CC-16 12V
JST-6 |
CC-40
JST-6 |
CC-46
Molex-6 |
CC-62
Molex-7 |
CC-33,-37
JST-3 |
Universal
JST-6 |
|
Pin 1 |
1K to Ground |
Inhibit |
/Tilt |
Inhibit |
Ground |
24 VDC/AC |
Inhibit |
|
Pin 2 |
Sense |
Sense |
Inhibit |
/Tilt |
/Sense |
Sense |
/Coin Optics |
|
Pin 3 |
48 VDC/AC |
----- |
/Credit |
/Credit |
/Tilt |
Ground |
----- |
|
Pin 4 |
24 VDC/AC |
24 VDC/AC |
24 VDC/AC |
/Sense |
/Credit |
|
24 VDC/AC |
|
Pin 5 |
12 VDC |
12 VDC |
12 VDC |
12 VDC |
Key Pin |
|
----- |
|
Pin 6 |
Ground |
Ground |
Ground |
Ground |
12 VDC |
|
Ground |
|
Pin 7 |
|
|
|
|
Inhibit |
|
|
Personality
Plug Model: |
PPNRI-6 |
PPNRI-3 |
PPIGTDC |
PPCDS |
PPSIGMA |
PPCWR |
PPMOX |
Compatibility
Connector |
NRI
10pin IDC |
NRI
10pin IDC |
IGT DC Slots
Molex-6 |
JST-6 |
Molex-7 |
Wires |
Wires |
|
Pin 1 |
Ground |
Ground |
Inhibit |
/Tilt |
Ground |
Yel-24VAC |
Yel - 24VAC |
|
Pin 2 |
12VDC |
12VDC |
/Sense |
Inhibit |
Sense |
Red - Relay |
Blk - Grnd |
|
Pin 3 |
/Output5 |
----- |
----- |
/Credit |
/Credit-A |
Red - Relay |
Wht -
Inhibit |
|
Pin 4 |
/Output6 |
----- |
----- |
24VAC |
/Credit-B |
Blk - Ground |
Blu - /Out1 |
|
Pin 5 |
Coin Return |
----- |
12 VDC |
+12VDC |
----- |
|
Pur - /Out2 |
|
Pin 6 |
Inhibit |
Inhibit |
Ground |
Ground |
+12VDC |
|
Brn - /Out3 |
|
Pin 7 |
/Output1 |
/Output1 |
|
|
Inhibit |
|
|
|
Pin 8 |
/Output2 |
/Output2 |
|
|
|
|
|
|
Pin 9 |
/Output3 |
/Output3 |
|
|
|
|
|
|
Pin 10 |
/Output4 |
----- |
|
|
|
|
|
Electrical Specifications For IDX Xeptors
|
SIGNAL: |
ELECTRICAL
CHARACTERISTICS
(Note: Pulse widths
programmable via "P"
command on serial port) |
|
INHIBIT |
Inhibit = float or >3.5VDC,
Enable = < 1.0VDC |
|
SENSE |
Active high 32ms pulse, PNP 12V
pull-up 10mA max, 3.3K pull-down. |
|
/SENSE |
Active low 32ms pulse, NPN
sinking 10mA max, 47K 5V pull-up. |
|
/CREDIT |
Active low 32ms pulse, NPN
sinking 10mA max, 47K 5V pull-up. |
|
/TILT |
Active low >32ms pulse, NPN
sinking 10mA max, 47K 5V pull-up. |
|
/OUTPUT-n |
Active low >32ms pulse, NPN
sinking 10mA max, 47K 5V pull-up. |
|
RELAY |
Relay contact terminal. 40V 0.2A
peak rating.. |
|
/Coin Optics |
Wire-OR optics output enable,
100ms low pulse, 100K 12V pull-up. |
|
48VDC/VAC |
Power input 38 to 55VDC, 38 to
55VAC, 35mA max @idle. |
|
24VDC/VAC |
Power input 14 to 32VDC, 16 to
32VAC, 35mA max @idle. |
|
12VDC |
Power input 11.5 to 16VDC, 25mA
max @idle, 240mA accept gate. |
|
1K to Ground |
1K 1W resistor to circuit ground.
(for triac holding current) |
|
Ground |
Circuit common. |
|
